-40%

Dyna 2000i Ultima Programmable Single Fire Electronic Ignition Module Harley

$ 76.52

Availability: 1426 in stock

Description

BRAND NEW
Part# 53-644
Fits: S&S, Harley Evolution, Ultima, Revtech, Shovelhead, & any Evolution based motors.
Will NOT fit EFI models
1970-1999 Carbed Big Twin Harley Models & 1971-2003 Sportster models except 1200S Sport.
You will get this brand new ignition exactly as pictured.
Dynatek makes Ultima's new ignitions used in their El Bruto motors.
These are brand new, not take offs.
The 2Ki not only adds to, but extends many features of the best selling Dyna 2000 module out of sight in a completely new design that fits under the cam cover.
The Dyna 2KiP (Programmable) is the newest addition to the successful line of Dyna 2000 ignition systems.
All features of the 2Ki switches are also included.
Features:
Single Fire operation down to zero rpm for easier cranking and kicking.
Will operate in all combinations of single fire or dual fire with single plug or dual plug heads.
(when used with appropriate coils)
8 advance curves to cover a broad range of engine builds and riding styles.
Engine over rev protection adjustable from 6000 to 7500 rpm.
Adjustable timing retard for nitrous and turbo applications.
VOES indicator. Allows you to tell at a glance the status of the VOES switch. Also indicates when retard mode is active. Great for diagnosing faulty vacuum switches or operation of retard controllers.
Built in Tach Driver. Delivers stable tach signal even during rev limiting or can be used to activate shift lights, auto shifters, and other accessories.
Easy static timing with built in timing indicator. No timing light required.
Intelligent over current / short circuit protection. Every time power to the ignition is switched on, the 2Ki will check to see if the coil is shorted, mis-wired, or the wrong type. If an error is detected, the 2Ki will immediately switch off and issue a warning by rapidly flashing the status indicator. Besides protecting the unit, this also prevents the costly failure of an improperly matched coil going bad one hour into your ride. After starting, the 2Ki continuously monitors the coil and wiring status.
Active Dwell Control. Continually adjusts coil current to maintain maximum spark energy all the way to redline while eliminating coil stress caused by overcharging at idle. High efficiency design reduces battery draw for easier cold whether starting and lower charging system load.
Ruggedized output - cannot be damaged by broken or disconnected spark plug wires.
Over voltage protected against momentary spikes (both positive and negative going) as well as surges caused by faulty voltage regulators or quick charge battery boosters.
Harness constructed with TXL cross linked polyethylene automotive wire for exceptional resistance to abrasion, heat, and chemical attack. High temp glass braid jacket further increases the toughness of the harness and provides a tight, clean appearance. Wire colors closely match the factory harness for error free installation.
Manufactured with premium quality components specifically qualified for operation in a high temperature / high vibration environment. A one piece aluminum housing and thermally conductive epoxy encapsulation provide superior heat dissipation and outstanding resistance to shock, vibration, and moisture.
Advanced microprocessor technology.
Quartz crystal accuracy.
Intelligent overvoltage/overcurrent protection.
Adjustable retard timing.
Short circuit protection.
All 2Ki ignitions are also PC Programmable with the optional programming kit part# 53-646:
EIGHT POINT FULLY DEFINABLE WIDE OPEN THROTTLE CURVE
EIGHT POINT FULLY DEFINABLE PART THROTTLE CURVE
REV LIMIT PROGRAMMABLE IN 50 RPM STEPS
PROGRAMMABLE DEAD CRANKING REVS 0-10
PROGRAMMABLE REAR CYLINDER OFFSET, TOTAL OF +/- 10 DEGREES
Data Recording:
TOTAL ENGINE HOURS
TIME AT WIDE OPEN THROTTLE
NUMBER OF ENGINE STARTS (TWO MINUTES RUNNING COUNTS AS ONE)
LONGEST TIME OPERATING AT WIDE OPEN THROTTLE
MAXIMUM RPM
SECONDS NEAR REV LIMIT
STATISTICAL ANALYSIS OF TIME AT RPM
1982 & EARLIER MODELS WILL REQUIRE A SENSOR CUP, OEM# 32402-83